Designing for Disassembly: What a Discarded Leather Armchair Teaches Student Artists
How can student artists turn one discarded object into multiple new works? The answer this lesson proposes is designing for disassembly: take the object apart in a planned sequence, map how its material varies from zone to zone, budget that material against a series of small functional forms, then build with the next teardown in mind. Designboom documents Jan Micha Gamer's bulky-waste leather armchair becoming nine domestic objects, from a floor basket and lamp to a pouf, picture frame, cabinet, carpet and table; the excerpt records the outcome, not his process, so the exercises below are our suggested adaptation for a studio scale students can replicate with found furniture.
Stage 1: Read the object before cutting it
Designboom's excerpt documents the outcome of Jan Micha Gamer's project: a bulky-waste leather armchair becoming nine functional domestic objects, from a floor basket, candleholder and lamp to a fruit basket, pouf, picture frame, cabinet, carpet and table. What the source does not record is how he took the chair apart, so the studio method below is our suggested adaptation rather than a reconstruction of his practice. The observation it builds on is that a found object's salvage value depends on how it was assembled: parts held by screws, clips or stitching can come free as whole components, while parts joined other ways may need cutting, and the largest usable surfaces tend to come from components released intact. Reading the assembly before cutting is therefore the first step our exercise proposes.
Our suggested exercise is a sequence teardown. Students photograph an intact bulky-waste chair or similar find from all sides, then take it apart step by step, photographing each stage and labelling what actually held the parts together at that step, whether stitching, screws, staples, clips or adhesive. The result is a numbered teardown sequence recording which joints released without cutting and which needed cutting. Two constraints apply: the record describes this particular object only, so any pattern a student notices about fastener behaviour is a hypothesis to test on their own offcuts in a later stage, not a conclusion; and the sequence should be written so another student could follow it. To evaluate the result, check each numbered step against its photograph and named fastener, count how many joints released without cutting, and measure the largest intact panel recovered.
Stage 2: Map how one material varies across the object
Designboom's excerpt lists the nine objects Jan Micha Gamer's armchair became, a floor basket, candleholder, lamp, fruit basket, pouf, picture frame, cabinet, carpet and table, but records nothing about how the leather itself behaved across the chair. That gap motivates the observation behind this stage, which we offer as a hypothesis to test, not a documented finding: the material recovered from a single object may not be uniform, since different zones of a used chair can carry different wear and handling, and treating the recovered panels as one undifferentiated stock would leave that variation unrecorded. The method we propose is a variation map. Students divide the largest recovered material, such as the leather panels, into zones on an outline drawing of the chair, then record a few simple measures they choose themselves for each zone.
Our suggested exercise continues with three measures per zone: thickness taken with a caliper or pin gauge, how far a swatch bends around dowels of different diameters before it creases, and a short note on surface wear. The finished map shows where this particular hide reads thick, thin, stiff, supple or worn, but its standing is deliberately narrow: it is evidence about this hide under these tests, not a statement about what leather does in general, and a classmate mapping a different armchair should expect a different map. To evaluate the result, pick two zones at random and repeat their tests; readings that land close to the recorded values suggest the map is repeatable, while a zone whose entry names no test method marks a gap to redo before the material is budgeted in the next stage.
Stage 3: Budget the material against a series of forms
Designboom's excerpt names the nine things Jan Micha Gamer's armchair became, a floor basket, candleholder, lamp, fruit basket, pouf, picture frame, cabinet, carpet and table, but records nothing about how one hide got divided among them. That gap is where this stage starts, and we offer the idea behind it as a hypothesis rather than a documented finding: the leather recovered from a single chair only has so much usable area, so a series built from it is largely a budgeting problem, with every candidate object competing for the same panels and the plan needing its demands to fit what was actually recovered. Treating allocation as a quantity-and-fit calculation, instead of guessing which object deserves the good leather, is the observation our exercise builds on.
Our suggested exercise is mockup yield budgeting. Students pick a few candidate forms at the scale Gamer's series suggests, say a basket, a lamp, a pouf, a frame, a cabinet panel, a carpet strip or a table, build quick paper or cardboard mockups, then flatten or unwrap each one to measure how much area its panels would demand. Comparing those totals against the stage 2 map, they assign hide zones to objects, for instance putting worn zones where wear reads as character and saving the most supple ones for forms that fold, though these pairings are suggestions to try out, not rules about what any object category requires. To evaluate the result, sum each object's demand against its assigned zones, confirm the whole series fits the hide, and cut one real panel as a spot check.
Stage 4: Build with the next teardown in mind
Designboom's excerpt lists what Jan Micha Gamer's armchair became, a floor basket, candleholder, lamp, fruit basket, pouf, picture frame, cabinet, carpet and table, but says nothing about how those new pieces were joined, so whether they were built to come apart again is not recorded. That gap frames the observation for this final stage, which we offer as a hypothesis rather than a documented finding: a series made from salvaged material may keep its salvage value open only where the new work can itself be undone, and whether undoable joints actually make a piece more salvageable is exactly what a student can test on their own build. The method our stage proposes is therefore to treat joinery as a decision made from evidence, with each joint selected after checking its behaviour on the maker's own offcuts.
Our suggested exercise is a reversible-join build with a future teardown sheet. Students build the first object of their series using joints chosen after offcut tests, for instance comparing a stitched seam against an adhesive-bonded seam on identical scraps and recording which released more cleanly in their own trial, since behaviour can vary with adhesive, stitch and material. They then attach a one-page sheet explaining how the finished piece comes apart: which joints are mechanical, which are not, and what a future maker would need to know. The sheet must describe the piece as actually built, not as planned. To evaluate the result, a classmate uses only the sheet to locate one joint, takes it apart and reassembles it, recording damage, tools and time; the rehearsal yields evidence about this build, not a guaranteed outcome.
Sources
- discarded leather armchair deconstructs into nine functional domestic objects — www.designboom.com,